Main Components of a PLC System: Complete Guide for Engineers
Master PLC system components: CPU, power supply, I/O modules, communication interfaces, and software with sizing formulas and selection tips. Shop at Stoklink.
- Part number
- 6EP3322-6SB10-0AY0
- Model no
- LOGO!Power
SITOPSiemens 6EP3322-6SB10-0AY0 LOGO!Power 100-240V AC / 15V DC 4A Power Supply
Siemens 6EP3322-6SB10-0AY0 LOGO!Power, 100-240V AC in, 15V DC/4A out, 88.4% efficiency, DIN rail, IP20.
Description
About the LOGO!Power
About the LOGO!Power
The Siemens 6EP3322-6SB10-0AY0 LOGO!Power supply converts a 100-240 V AC (or 110-300 V DC) wide-range input into a stabilized, adjustable 15 V DC output rated at 4 A. It reaches 88.4% efficiency, provides 40 ms buffering time on power loss, and snaps onto a 35 mm DIN rail in an IP20, Class II enclosure for direct control-cabinet mounting.
Certifications & Standards
- CE
- UL 508
- cULus
- EAC
- NEC Class 2
- SEMI F47
- CB
Selection Notes
The output voltage is adjustable from 10.5 to 16.1 V via an onboard potentiometer, so this unit covers applications that need slightly above or below the nominal 15 V rail, not just a fixed 15 V. It supports parallel operation of up to two units to increase available power, which matters if a load exceeds the single-unit 60 W rating. The 40 ms power-loss buffering time is a spec to check against downstream PLC or relay hold-in requirements before assuming ride-through on brief mains dips.
Applications
Sized for LOGO! logic modules and small 15 V DC loads such as relay coils, sensors, or signal circuits in control cabinets, machine builds, and building-automation panels where DIN-rail mounting and a wide 100-240 V AC input range are needed.
Specification
Full specification
General information 4
| product brand name | LOGO!Power |
|---|---|
| product type designation | LOGO!Power |
| product designation | Power supply LOGO!Power |
| type of current supply | 15 V/4 A |
Input 21
| type of the power supply network | 1-phase AC or DC |
|---|---|
| phase number | 1 |
| voltage curve at input | AC/DC |
| supply voltage at AC: minimum rated value | 100 V |
| supply voltage at AC: maximum rated value | 240 V |
| supply voltage at AC: initial value | 85 V |
| supply voltage at AC: full-scale value | 264 V |
| input voltage at DC | 110 ... 300 V |
| supply voltage: at 50 Hz | 240 V |
| supply voltage: at 60 Hz | 100 V |
| line frequency | 50/60 Hz |
| wide range input | Yes |
| overvoltage overload capability | 300 V AC for 1 s |
| buffering time for rated value of the output current in the event of power failure minimum | 40 ms |
| operating condition of the mains buffering | at Vin = 187 V |
| input current: at rated input voltage 120 V | 1.24 A |
| input current: at rated input voltage 230 V | 0.68 A |
| current limitation of inrush current at 25 °C maximum | 55 A |
| I2t value maximum | 3 A2·s |
| fuse protection type | internal |
| fuse protection type in the feeder | Recommended miniature circuit breaker: from 10 A characteristic B or from 6 A characteristic C |
Output 23
| voltage curve at output | Controlled, isolated DC voltage |
|---|---|
| product function output voltage controlled | Yes |
| product function output voltage stabilized | Yes |
| output voltage at DC rated value | 15 V |
| output voltage: at output 1 at DC rated value | 15 V |
| output voltage: at output 1 at DC | 15 V |
| output voltage adjustable | Yes; via potentiometer |
| adjustable output voltage | 10.5 ... 16.1 V |
| relative overall tolerance of the voltage | 3% |
| relative control precision of the output voltage: on slow fluctuation of input voltage | 0.1 % |
| residual ripple: maximum | 200 mV |
| residual ripple: typical | 30 mV |
| voltage peak: maximum | 300 mV |
| voltage peak: typical | 50 mV |
| display version for normal operation | Green LED for output voltage OK |
| behavior of the output voltage when switching on | No overshoot of Vout (soft start) |
| response delay maximum | 0.5 s |
| voltage increase time of the output voltage: typical | 100 ms |
| output current: rated value | 4 A |
| output current: rated range | 0 ... 4 A; +55 ... +70 °C: Derating 2%/K |
| supplied active power typical | 60 W |
| bridging of equipment | Yes |
| number of parallel-switched equipment resources for increasing the power | 2 |
Show all 129 specifications ↓ Show less ↑81 more values in Identification, Efficiency, Closed-loop control, Protection and monitoring, Safety, EMC, Standards, specifications, approvals, Standards, specifications, approvals hazardous environments, Standards, specifications, approvals marine classification, Standards, specifications, approvals Environmental Product Declaration, Ambient conditions, Connection method, Mechanical data, Additional information, Approvals Certificates, Logistics.
Identification 10
| Part number | 6EP3322-6SB10-0AY0 |
|---|---|
| Type designation | LOGO!Power |
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Active, in production |
| EAN | 4025515154839 |
| ETIM class | EC002540 |
| eCl@ss | 27040701 |
Efficiency 3
| efficiency in percent | 88.4 % |
|---|---|
| power loss [W]: at rated output voltage for rated value of the output current typical | 7.9 W |
| power loss [W]: during no-load operation maximum | 0.3 W |
Closed-loop control 4
| relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical | 0.2 % |
|---|---|
| relative control precision of the output voltage at load step of resistive load 10/90/10 % typical | 3% |
| setting time: load step 10 to 90% typical | 1 ms |
| setting time: load step 90 to 10% typical | 1 ms |
Protection and monitoring 8
| design of the overvoltage protection | < 60 V |
|---|---|
| property of the output short-circuit proof | Yes |
| design of short-circuit protection | Constant current characteristic |
| typical | 5 A |
| overcurrent overload capability: when switching on | 150% Iout rated typ. 200 ms |
| overcurrent overload capability: in normal operation | overload capability 150% Iout rated typ. 200 ms |
| enduring short circuit current RMS value: maximum | 5 A |
| measuring point for output current | Yes; 45 mV =^ 4 A |
Safety 4
| electrical separation between input and output | Yes |
|---|---|
| galvanic isolation | Output voltage: SELV, ES1 (IEC 62368-1), DVC As (IEC 61204-7) |
| operating resource protection class | Class II (without protective conductor) |
| protection class IP | IP20 |
EMC 3
| standard: for emitted interference | EN 55022 Class B |
|---|---|
| standard: for mains harmonics limitation | not applicable |
| standard: for interference immunity | EN 61000-6-2 |
Standards, specifications, approvals 7
| certificate of suitability: CE marking | Yes |
|---|---|
| certificate of suitability: UL approval | Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus- Recognized (UL 60950, CSA C22.2 No. 60950), File E151273, NEC class 2 (acc. to UL 1310) |
| certificate of suitability: EAC approval | Yes |
| certificate of suitability: NEC Class 2 | Yes; according to UL1310, File E151273 |
| certificate of suitability: SEMI F47 | Yes |
| type of certification: CB-certificate | Yes |
| MTBF at 40 °C | 2 566 680 h |
Standards, specifications, approvals hazardous environments 4
| certificate of suitability: IECEx | No |
|---|---|
| certificate of suitability: ATEX | No |
| certificate of suitability: ULhazloc approval | No |
| certificate of suitability: FM registration | No |
Standards, specifications, approvals marine classification 5
| shipbuilding approval | Yes |
|---|---|
| Marine classification association: American Bureau of Shipping Europe Ltd. (ABS) | Yes |
| Marine classification association: French marine classification society (BV) | Yes |
| Marine classification association: Det Norske Veritas (DNV) | Yes |
| Marine classification association: Lloyds Register of Shipping (LRS) | Yes |
Standards, specifications, approvals Environmental Product Declaration 6
| Environmental Product Declaration | Yes |
|---|---|
| global warming potential [CO2 eq]: total | 220 kg |
| global warming potential [CO2 eq]: during manufacturing | 3.8 kg |
| global warming potential [CO2 eq]: during operation | 216 kg |
| global warming potential [CO2 eq]: after end of life | 0.14 kg |
| Siemens eco profile (SEP) | Siemens EcoTech |
Ambient conditions 4
| ambient temperature: during operation | -25 ... +70 °C; with natural convection |
|---|---|
| ambient temperature: during transport | -40 ... +85 °C |
| ambient temperature: during storage | -40 ... +85 °C |
| environmental category according to IEC 60721 | Climate class 3K3, 5 ... 95% no condensation |
Connection method 4
| type of electrical connection | screw terminal |
|---|---|
| at input | L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded |
| at output | +, -: 1 screw terminal each for 0.5 ... 2.5 mm2 |
| for auxiliary contacts | - |
Mechanical data 11
| width × height × depth of the enclosure | 54 × 90 × 53 mm |
|---|---|
| installation width × mounting height | 54 mm × 130 mm |
| required spacing: top | 20 mm |
| required spacing: bottom | 20 mm |
| required spacing: left | 0 mm |
| required spacing: right | 0 mm |
| fastening method | Snaps onto DIN rail EN 60715 35x7.5/15, direct mounting in different mounting positions |
| DIN-rail mounting | Yes |
| S7 rail mounting | No |
| wall mounting | Yes |
| housing can be lined up | Yes |
Additional information 1
| other information | Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) |
|---|
Approvals Certificates 1
| Environmental Product Declaration: global warming potential [CO2 eq] / during manufacturing | 3.8 kg |
|---|
Logistics 6
| Net weight | 0.2 kg |
|---|---|
| Country of origin | Romania |
| Shipping weight | 0.7 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
Documents
Documents for 6EP3322-6SB10-0AY0
No documents are on file for this part yet.
Ask us for the datasheet
Certifications
Certifications and standards
- CE marking
- EAC approval
- SEMI F47
- CB-certificate
- shipbuilding approval
- American Bureau of Shipping Europe Ltd. (ABS)
- French marine classification society (BV)
- Det Norske Veritas (DNV)
- Lloyds Register of Shipping (LRS)
- Environmental Product De
Quick answers
Questions about the LOGO!Power
What is the rated current of LOGO!Power?
The rated current of LOGO!Power is 4 A.
Which supply voltage is LOGO!Power rated for?
The rated operational voltage of LOGO!Power is 100–240 V AC.
What motor power is LOGO!Power rated for?
The rated motor power of LOGO!Power is 7.9 W kW.
What is the HS code of LOGO!Power for customs?
The tariff (HS) code on file for LOGO!Power is 85044083.
What is the EAN of LOGO!Power?
The EAN (GTIN) of LOGO!Power is 4025515154839.
Where does LOGO!Power ship from, and how fast?
LOGO!Power ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
Guides
Guides for power supplies
Reviews
Customer reviews
Series
Siemens SITOP
- Brand
- Siemens
- Series
- SITOP
