Main Components of a PLC System: Complete Guide for Engineers
Master PLC system components: CPU, power supply, I/O modules, communication interfaces, and software with sizing formulas and selection tips. Shop at Stoklink.
- Part number
- 6EP1333-7CA10
- Model no
- PSU100P
- CE
- EAC
SITOP PSU100PSiemens 6EP1333-7CA10 SITOP PSU100P IP67 24V/5A M12 Field Power Supply
SITOP PSU100P IP67 24V/5A field power supply, M12 L-coded output, 120/230V AC input.
Description
About the PSU100P
About the PSU100P
The Siemens 6EP1333-7CA10 is a SITOP PSU100P power supply built for IP67 field mounting outside the control cabinet. It takes 120 V or 230 V AC with automatic range selection and delivers a stabilized 24 V DC output rated 5 A (133 W) through an M12 L-coded output connector, with a 7/8-inch input plug and a separate M12 alarm connector for the 24 V OK signal.
Certifications & Standards
- CE
- EAC
Selection Notes
The IP67 rating and M12/7/8-inch plug connectors let the 6EP1333-7CA10 mount directly on a machine frame or outside a cabinet, where the DIN-rail and wall-mount SITOP models need an enclosure. At 5 A / 133 W it sits below the higher-current variant in the same connectorized PSU100P family, so it fits a single field device or a small distributed I/O drop rather than a full remote panel. The relay contact on the alarm connector reports the 24 V OK status without running a separate signal back to the control cabinet, and the 90% efficiency keeps self-heating low inside a sealed enclosure where convection cooling is limited.
Specification
Full specification
General information 4
| product brand name | SITOP |
|---|---|
| product type designation | PSU100P |
| product designation | Power supply SITOP |
| type of current supply | 24 V/5 A |
Input 20
| type of the power supply network | 1-phase AC |
|---|---|
| phase number | 1 |
| voltage curve at input | AC |
| supply voltage at AC | Automatic range selection |
| supply voltage | 120 V/230 V |
| input voltage 1 at AC | 85 ... 132 V |
| input voltage 2 at AC | 170 ... 264 V |
| supply voltage: at 50 Hz | 230 V |
| supply voltage: at 60 Hz | 120 V |
| line frequency | 50/60 Hz |
| wide range input | No |
| overvoltage overload capability | Implemented internally with varistor |
| buffering time for rated value of the output current in the event of power failure minimum | 40 ms |
| operating condition of the mains buffering | at Vin = 120/230 V |
| input current: at rated input voltage 120 V | 2.25 A |
| input current: at rated input voltage 230 V | 1.24 A |
| current limitation of inrush current at 25 °C maximum | 15 A |
| I2t value maximum | 0.6 A2·s |
| fuse protection type | T 3.15 A |
| fuse protection type in the feeder | Recommended miniature circuit breaker: from 6 A characteristic C/B |
Output 26
| voltage curve at output | Controlled, isolated DC voltage |
|---|---|
| product function output voltage controlled | Yes |
| product function output voltage stabilized | Yes |
| output voltage at DC rated value | 24 V |
| output voltage: at output 1 at DC rated value | 24 V |
| output voltage: at output 1 at DC | 24 V |
| output voltage adjustable | No |
| relative overall tolerance of the voltage | 3% |
| relative control precision of the output voltage: on slow fluctuation of input voltage | 0.1 % |
| residual ripple: maximum | 50 mV |
| voltage peak: maximum | 100 mV |
| display version for normal operation | Green LED: 24 V OK; red LED flashing: "overload/short-circuit" |
| type of signal at output | Relay contact (NO contact, rating 30 V AC/ 0.5 A; 30 V DC/1 A) for 24 V OK |
| behavior of the output voltage when switching on | Overshoot of Vout < 3 % |
| response delay maximum | 1.5 s |
| voltage increase time of the output voltage: typical | 22 ms |
| voltage increase time of the output voltage: maximum | 100 ms |
| output current: rated value | 5 A |
| output current: rated range | 0 ... 5 A |
| supplied active power typical | 133 W |
| short-term overload current: on short-circuiting during the start-up typical | 20 A |
| short-term overload current: at short-circuit during operation typical | 20 A |
| duration of overloading capability for excess current: on short-circuiting during the start-up | 50 ms |
| duration of overloading capability for excess current: at short-circuit during operation | 50 ms |
| bridging of equipment | Yes; Symmetric wiring required |
| number of parallel-switched equipment resources for increasing the power | 2 |
Show all 125 specifications ↓ Show less ↑75 more values in Identification, Efficiency, Closed-loop control, Protection and monitoring, Safety, EMC, Standards, specifications, approvals, Standards, specifications, approvals hazardous environments, Standards, specifications, approvals marine classification, Ambient conditions, Connection method, Mechanical data, Version Classification, Logistics.
Identification 10
| Part number | 6EP1333-7CA10 |
|---|---|
| Type designation | PSU100P |
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Active, in production |
| EAN | 4025515156338 |
| ETIM class | EC002540 |
| eCl@ss | 27040701 |
Efficiency 2
| efficiency in percent | 90 % |
|---|---|
| power loss [W]: at rated output voltage for rated value of the output current typical | 12.9 W |
Closed-loop control 3
| relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical | 0.2 % |
|---|---|
| relative control precision of the output voltage load step of resistive load 50/100/50 % typical | 1% |
| setting time: maximum | 2 ms |
Protection and monitoring 7
| design of the overvoltage protection | < 29 V |
|---|---|
| property of the output short-circuit proof | Yes |
| design of short-circuit protection | Electronic shutdown, automatic restart |
| typical | 5.5 A |
| enduring short circuit current RMS value: maximum | 6 A |
| enduring short circuit current RMS value: typical | 5 A |
| display version for overload and short circuit | Red LED flashing for "overload/short-circuit" |
Safety 6
| electrical separation between input and output | Yes |
|---|---|
| galvanic isolation | Output voltage: SELV, ES1 (IEC 62368-1), DVC As (IEC 61204-7) |
| operating resource protection class | Class I |
| leakage current: maximum | 3.5 mA |
| leakage current: typical | 1 mA |
| protection class IP | IP67 |
EMC 3
| standard: for emitted interference | EN 55022 Class B |
|---|---|
| standard: for mains harmonics limitation | EN 61000-3-2 |
| standard: for interference immunity | EN 61000-6-2 |
Standards, specifications, approvals 6
| certificate of suitability: CE marking | Yes |
|---|---|
| certificate of suitability: UL approval | Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1) |
| certificate of suitability: EAC approval | Yes |
| certificate of suitability: NEC Class 2 | No |
| type of certification: CB-certificate | No |
| MTBF at 40 °C | 1 500 000 h |
Standards, specifications, approvals hazardous environments 4
| certificate of suitability: IECEx | No |
|---|---|
| certificate of suitability: ATEX | No |
| certificate of suitability: ULhazloc approval | No |
| certificate of suitability: FM registration | No |
Standards, specifications, approvals marine classification 5
| shipbuilding approval | No |
|---|---|
| Marine classification association: American Bureau of Shipping Europe Ltd. (ABS) | No |
| Marine classification association: French marine classification society (BV) | No |
| Marine classification association: Det Norske Veritas (DNV) | No |
| Marine classification association: Lloyds Register of Shipping (LRS) | No |
Ambient conditions 4
| ambient temperature: during operation | -25 ... +60 °C; with natural convection |
|---|---|
| ambient temperature: during transport | -40 ... +85 °C |
| ambient temperature: during storage | -40 ... +85 °C |
| environmental category according to IEC 60721 | 3K6 without direct sunlight |
Connection method 6
| type of electrical connection | screw terminal |
|---|---|
| at input | L1, N, PE: Plug connector 7/8" (counterpart see "Operating Instructions (compact)") |
| at output | +, -: Plug connector M12-L coded (counterpart see "Operating Instructions (compact)") |
| for auxiliary contacts | Alarm signals: M12 plug-in connector 4-pin |
| removable terminal at input | Yes |
| removable terminal at output | Yes |
Mechanical data 11
| width × height × depth of the enclosure | 120 × 181 × 60.5 mm |
|---|---|
| installation width × mounting height | 120 mm × 170 mm |
| required spacing: top | 50 mm |
| required spacing: bottom | 0 mm |
| required spacing: left | 0 mm |
| required spacing: right | 0 mm |
| fastening method | Wall mounting |
| DIN-rail mounting | No |
| S7 rail mounting | No |
| wall mounting | Yes |
| housing can be lined up | Yes |
Version Classification 2
| eClass | 16 27-04-07-01 |
|---|---|
| ETIM | 10 EC002540 |
Logistics 6
| Net weight | 1.1 kg |
|---|---|
| Country of origin | HU |
| Shipping weight | 1.6 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
Documents
Documents for 6EP1333-7CA10
No documents are on file for this part yet.
Ask us for the datasheet
Certifications
Certifications and standards
- CE
- EAC
- CE marking
- EAC approval
Quick answers
Questions about the PSU100P
What is the rated current of PSU100P?
The rated current of PSU100P is 5 A.
Which supply voltage is PSU100P rated for?
The rated operational voltage of PSU100P is 120–230 V AC.
What motor power is PSU100P rated for?
The rated motor power of PSU100P is 12.9 W kW.
What is the HS code of PSU100P for customs?
The tariff (HS) code on file for PSU100P is 85044083.
What is the EAN of PSU100P?
The EAN (GTIN) of PSU100P is 4025515156338.
Where does PSU100P ship from, and how fast?
PSU100P ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
Guides
Guides for power supplies
Reviews
Customer reviews
Series
Siemens SITOP PSU100P
- Brand
- Siemens
- Series
- SITOP PSU100P
