How to Select an Interface Relay for PLC Outputs
A step-by-step guide to matching PLC output type, coil voltage and current, contact rating, and socket style when selecting an interface relay.
The Siemens 6ES7545-5DA00-0AB0 is a SIMATIC ET 200SP communication module, type CM PROFIBUS DP, that plugs onto an ET 200SP CPU to add a PROFIBUS DP interface on a 9-pin D-sub socket. It can operate as a DP master for up to 125 DP slaves or as a DP slave itself, at transmission rates up to 12 Mbit/s with automatic baud rate detection.
Supporting up to 125 DP slaves as a master, this module handles a full PROFIBUS DP segment from a single ET 200SP station, which is the reason to add it rather than route legacy PROFIBUS devices through a separate gateway. It can also run as a DP slave, so an ET 200SP station built around this CPU module can itself be integrated as a remote node on an existing PROFIBUS master system during a migration to PROFINET. The 244-byte input and 244-byte output transfer memory and 128-byte-per-address-area limit set the ceiling on how much process data can move per DP cycle; large legacy DP installations should check these limits against total connected slave data before specifying this module.
Adding PROFIBUS DP master or slave capability to an ET 200SP CPU for integrating legacy PROFIBUS drives, sensors, or remote I/O during a phased migration to PROFINET.
| Product type designation | CM PROFIBUS DP |
|---|---|
| HW functional status | FS04 |
| Engineering with: STEP 7 TIA Portal configurable/integrated from version | V13 Update 3 |
| Rated value (DC) | 24 V |
|---|---|
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Interface types: RS 485 | Yes |
|---|---|
| Protocols: PROFIBUS DP master | Yes |
| Protocols: PROFIBUS DP device | Yes |
| Protocols: SIMATIC communication | Yes |
| PROFIBUS DP master: max. number of DP devices Services | 125 |
| PROFIBUS DP master: PG/OP communication | Yes |
| PROFIBUS DP master: Equidistance | No |
| PROFIBUS DP master: Isochronous mode | No |
| PROFIBUS DP master: activation/deactivation of DP devices | Yes |
| PROFIBUS DP device: Transmission rate, max. | 12 Mbit/s |
| PROFIBUS DP device: automatic baud rate search | Yes |
| PROFIBUS DP device: Address area, max. | 120 |
| PROFIBUS DP device: User data per address area, max. Services | 128 byte |
| PROFIBUS DP device: PG/OP communication | Yes; Only with active interface |
| PROFIBUS DP device: Routing | Yes; Only with active interface |
| PROFIBUS DP device: S7 communication | Yes; Only with active interface |
| PROFIBUS DP device: Direct data exchange (slave-to-slave communication) | Yes; No subscriber possible - only passive publisher |
| PROFIBUS DP device: DPV1 Transfer memory | Yes |
| PROFIBUS DP device: Inputs | 244 byte |
| PROFIBUS DP device: Outputs | 244 byte |
| Part number | 6ES7545-5DA00-0AB0 |
|---|---|
| Type designation | CM PROFIBUS DP |
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Active, in production |
| EAN | 4047623404538 |
| ETIM class | EC001604 |
| eCl@ss | 27242608 |
| RS 485: Transmission rate, max. | 12 Mbit/s |
|---|---|
| RS 485: Cable length, max. | 100 m |
| SIMATIC communication: S7 routing | Yes |
|---|---|
| SIMATIC communication: Data record routing | Yes |
| Diagnostics function | Yes |
|---|---|
| Diagnostics indication LED: for module diagnostics | Yes; green/red DIAG LED |
| between backplane bus and interface | Yes |
|---|
| Ambient temperature during operation: horizontal installation, min. | -25 °C; No condensation |
|---|---|
| Ambient temperature during operation: vertical installation, min. | -25 °C; No condensation |
| Altitude during operation relating to sea level: Installation altitude above sea level, max. | 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual |
| Width | 35 mm |
|---|---|
| Height | 117 mm |
| Depth | 75 mm |
| Weight, approx. | 80 g |
|---|
| Net weight | 0.105 kg |
|---|---|
| Country of origin | DE |
| Shipping weight | 0.605 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
No documents are on file for this part yet.
Ask us for the datasheetThe rated operational voltage of CM PROFIBUS DP is 24 V AC.
The tariff (HS) code on file for CM PROFIBUS DP is 85176200.
The EAN (GTIN) of CM PROFIBUS DP is 4047623404538.
CM PROFIBUS DP ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
A step-by-step guide to matching PLC output type, coil voltage and current, contact rating, and socket style when selecting an interface relay.
Compare the 5 main PLC types, IEC 61131-3 languages, scan-time sizing, and brand options to choose the right controller for your plant. Shop at...
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.