Part number
6ES7522-5FH00-0AB0
Model no
DQ 16x230VAC/1A ST (Triac)
$516.47 On request Dispatch — · From TürkiyeGet a Quote
SIMATIC S7-1500

Siemens 6ES7522-5FH00-0AB0 SIMATIC S7-1500 DQ 16x230VAC/1A ST Triac Digital Output PLC I/O Module

SIMATIC S7-1500 DQ 16x230VAC/1A ST, 16 Triac outputs, 6.3A slow-blow fuse per channel, 2A per group.

Rated current
1 A
Rated operational voltage
230 V AC
EAN
4047623404101
Description

About the DQ 16x230VAC/1A ST (Triac)

The Siemens 6ES7522-5FH00-0AB0 is a SIMATIC S7-1500 digital output module, DQ 16x230VAC/1A ST, switching 16 Triac outputs rated 1 A at 120/230 V AC and wired in groups of 2 channels. Each output carries a 6.3 A slow-blow fuse and a built-in switching cycle counter, and it needs a front connector ordered separately.

Selection Notes

ST places this module in the Standard performance class with per-channel diagnostics and an integrated switching-cycle counter, ahead of a Basic-class AC output module but below an HF-class card with tighter output delay. The Triac output stage is the reason to pick this over a relay-output AC module in the same voltage range: solid-state switching gives silent, contact-less operation and a rated 10 Hz switching frequency on resistive loads, at the cost of a lower NEMA motor-starter rating (size 4) than a relay-based card can carry. Because the built-in 6.3 A slow-blow fuse protects each channel individually, a channel fault does not take the whole group down, unlike output modules relying only on group-level external fusing.

Applications

Switching 120/230 V AC loads such as solenoid valves, small motor starters, and indicator lamps directly from the PLC, where solid-state Triac switching is preferred over relay contacts for cycle life or noise reasons.

Specification

Full specification

94 values · Last verified 01 Nov 2026

General information 17

Product type designation DQ 16x230VAC/1A ST (Triac)
HW functional status from FS01
Firmware version V 1.2.0
FW update possible Yes
Product function: I&M data Yes; I&M0 to I&M3
Product function: Isochronous mode No
Product function: Prioritized startup Yes
Engineering with: STEP 7 TIA Portal configurable/integrated from version V13 SP1 / -
Engineering with: STEP 7 configurable/integrated from version V5.5 SP3 / -
Engineering with: PROFIBUS from GSD version/GSD revision V1.0 / V5.1
Engineering with: PROFINET from GSD version/GSD revision V2.3 / -
Operating mode: DQ Yes
Operating mode: DQ with energy-saving function No
Operating mode: PWM No
Operating mode: Oversampling No
Operating mode: MSO Yes
Operating mode: Integrated operating cycle counter Yes; FW V1.2.0 or higher

Output voltage 1

Rated value (AC) 230 V; 120/230 V AC, 50/60 Hz

Power 1

Power consumption from the backplane bus 1.2 W
Show all 94 specifications ↓ Show less ↑75 more values in Identification, Power loss, Digital outputs, Interrupts/diagnostics/status information, Potential separation, Permissible potential difference, Isolation, Standards, approvals, certificates, Security, Ambient conditions, Dimensions, Weights, General Product Approval, General Product Approval For use in hazardous locations, Logistics.

Identification 10

Part number 6ES7522-5FH00-0AB0
Type designation DQ 16x230VAC/1A ST (Triac)
Brand Siemens
Condition New, factory sealed
Source Siemens and its authorised distributors
Warranty Manufacturer warranty
Lifecycle status Active, in production
EAN 4047623404101
ETIM class EC001419
eCl@ss 27242204

Power loss 1

Power loss, typ. 11.1 W

Digital outputs 28

Type of digital output Triac
Number of digital outputs 16
Current-sinking Yes
Current-sourcing Yes
Digital outputs, parameterizable Yes
Short-circuit protection No
built-in fuse 6.3 A melting fuse, slow-blow
Size of motor starters according to NEMA, max. 4
Switching capacity of the outputs: with resistive load, max. 1 A
Switching capacity of the outputs: on lamp load, max. 50 W
Output voltage: for signal "1", min. L1 (-1.5 V) at maximum output current; L1 (-8.5 V) at minimum output current
Output current: for signal "1" rated value 1 A
Output current: for signal "1" permissible range, min. 10 mA
Output current: for signal "1" permissible range, max. 15 A; max. 1 AC cycle
Output current: for signal "0" residual current, max. 2 mA
Output delay with resistive load: "0" to "1", max. 1 AC cycle
Output delay with resistive load: "1" to "0", max. 1 AC cycle
Parallel switching of two outputs: for logic links No
Parallel switching of two outputs: for uprating No
Parallel switching of two outputs: for redundant control of a load Yes
Switching frequency: with resistive load, max. 10 Hz
Switching frequency: with inductive load, max. 0.5 Hz
Switching frequency: on lamp load, max. 1 Hz
Total current of the outputs: Current per channel, max. 1 A; see additional description in the manual
Total current of the outputs: Current per group, max. 2 A; see additional description in the manual
Total current of the outputs: Current per module, max. 10 A; see additional description in the manual
Cable length: shielded, max. 1 000 m
Cable length: unshielded, max. 600 m

Interrupts/diagnostics/status information 13

Diagnostics function No
Substitute values connectable Yes
Alarms: Diagnostic alarm No
Alarms: Maintenance interrupt Yes; maintenance alarm for switching cycle counter
Diagnoses: Monitoring the supply voltage No
Diagnoses: Wire break No
Diagnoses: Short-circuit No
Diagnostics indication LED: RUN LED Yes; green LED
Diagnostics indication LED: ERROR LED Yes; red LED
Diagnostics indication LED: Monitoring of the supply voltage (PWR-LED) No
Diagnostics indication LED: Channel status display Yes; green LED
Diagnostics indication LED: for channel diagnostics No
Diagnostics indication LED: for module diagnostics Yes; red LED

Potential separation 3

Potential separation channels: between the channels No
Potential separation channels: between the channels, in groups of 2
Potential separation channels: between the channels and backplane bus Yes

Permissible potential difference 1

between different circuits 250 V AC between the channels and the backplane bus; 500 V AC between the channels

Isolation 1

Isolation tested with 3 100 V DC

Standards, approvals, certificates 1

Suitable for safety functions No

Security 2

signed firmware update No
data integrity No

Ambient conditions 2

Ambient temperature during operation: horizontal installation, min. 0 °C
Ambient temperature during operation: vertical installation, min. 0 °C

Dimensions 3

Width 35 mm
Height 147 mm
Depth 129 mm

Weights 1

Weight, approx. 310 g

General Product Approval 1

Miscellaneous Manufacturer Declara- tion

General Product Approval For use in hazardous locations 2

China RoHS Manufacturer Declara- FM tion
Maritime application NK / Nippon Kaiji Ky- okai

Logistics 6

Net weight 0.358 kg
Country of origin DE
Shipping weight 0.858 kg
Ships from Türkiye
Dispatch —
Stock On request

Source: manufacturer data · Last verified: 01 Nov 2026

Documents

Documents for 6ES7522-5FH00-0AB0

No documents are on file for this part yet.

Ask us for the datasheet
Quick answers

Questions about the DQ 16x230VAC/1A ST (Triac)

What is the rated current of DQ 16x230VAC/1A ST (Triac)?

The rated current of DQ 16x230VAC/1A ST (Triac) is 1 A.

Which supply voltage is DQ 16x230VAC/1A ST (Triac) rated for?

The rated operational voltage of DQ 16x230VAC/1A ST (Triac) is 230 V AC.

What is the HS code of DQ 16x230VAC/1A ST (Triac) for customs?

The tariff (HS) code on file for DQ 16x230VAC/1A ST (Triac) is 85389091.

What is the EAN of DQ 16x230VAC/1A ST (Triac)?

The EAN (GTIN) of DQ 16x230VAC/1A ST (Triac) is 4047623404101.

Where does DQ 16x230VAC/1A ST (Triac) ship from, and how fast?

DQ 16x230VAC/1A ST (Triac) ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.

Guides

Guides for PLC & controllers

All guides for PLC & controllers
Reviews

Customer reviews

Series

Siemens SIMATIC S7-1500

Brand
Siemens
Series
SIMATIC S7-1500
$516.47 On request
Get a Quote
Quote

Get a Quote

DQ 16x230VAC/1A ST (Triac)

Genuine parts

Genuine, factory-sealed parts

Siemens · 6ES7522-5FH00-0AB0

Every part on Stoklink is new, unused and made by the manufacturer named on the page.

Condition
New and unused, in the manufacturer's factory-sealed packaging.
Sourced from
Siemens and its authorised distributors.
Warranty
The manufacturer's warranty applies.
If a part is not genuine
We refund the full amount.

Added to cart Could not add to cart

View cart