Programmable Logic Controller Guide: Selection, Application, and Maintenance for Engineers
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Once production ends, supply depends on remaining stock.
No replacement announced yet. Tell us the application and we will propose an alternative.
The Siemens 6ES7422-7BL00-0AB0 SIMATIC S7-400 SM 422 module delivers 32 isolated 24 V DC digital outputs at 0.5 A each with parameterizable diagnostics: diagnostic alarm, hardware interrupt, wire-break detection below 0.15 mA, and short-circuit detection above roughly 1 A typical. Channels are isolated in groups of 8. Two outputs can be paralleled for uprating or redundant load control within the same group.
This 32-channel, 0.5 A module adds parameterizable diagnostics – diagnostic alarms, a hardware interrupt, wire-break detection below 0.15 mA, and short-circuit detection above roughly 1 A typical – all reported back to the CPU without extra external wiring. Choose it when the application needs to detect an open output wire or a shorted load automatically rather than through periodic manual checks. Parallel switching of two outputs is supported for both uprating current and redundant control within the same group. Channels are isolated in groups of 8, giving better circuit separation across mixed 24 V DC loads.
| Load voltage L+: Rated value (DC) | 24 V |
|---|---|
| Load voltage L+: permissible range, lower limit (DC) | 20.4 V |
| Load voltage L+: permissible range, upper limit (DC) | 28.8 V |
| from load voltage L+ (without load), max. | 120 mA |
|---|---|
| from backplane bus 5 V DC, max. | 200 mA |
| Power loss, typ. | 8 W |
|---|
| Part number | 6ES7422-7BL00-0AB0 |
|---|---|
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Phase-out announced by the manufacturer |
| EAN | 4025515128953 |
| Number of digital outputs | 32 |
|---|---|
| Short-circuit protection | Yes; Clocked electronically |
| Response threshold, typ. | 0.75 to 1.5 A |
| Limitation of inductive shutdown voltage to | L+ (-45 V) |
| Controlling a digital input | Yes; possible |
| Switching capacity of the outputs: on lamp load, max. | 5 W |
| Load resistance range: lower limit | 48 Ω |
| Load resistance range: upper limit | 4 kΩ |
| Output voltage: for signal "1", min. | L+ (-0.8 V) |
| Output current: for signal "1" rated value | 0.5 A |
| Output current: for signal "1" permissible range, min. | 5 mA |
| Output current: for signal "1" permissible range, max. | 600 A |
| Output current: for signal "0" residual current, max. | 0.5 mA |
| Parallel switching of two outputs: for uprating | Yes; possible (only outputs of the same group) |
| Parallel switching of two outputs: for redundant control of a load | Yes; possible (only outputs of the same group) |
| Switching frequency: with resistive load, max. | 100 Hz |
| Switching frequency: with inductive load, max. | 2 Hz |
| Switching frequency: with inductive load (acc. to IEC 60947-5-1, DC13), max. | 2 Hz |
| Switching frequency: on lamp load, max. | 2 Hz |
| Total current of the outputs (per group) all mounting positions: up to 40 °C, max. | 4 A |
| Cable length: shielded, max. | 1 000 m |
| Cable length: unshielded, max. | 600 m |
| Diagnostics function | Yes; Parameterizable |
|---|---|
| Alarms: Diagnostic alarm | Yes; Parameterizable |
| Alarms: Hardware interrupt | Yes; Parameterizable |
| Diagnoses: Diagnostic information readable | Yes |
| Diagnoses: Wire break | Yes; <0.15 mA |
| Diagnoses: Short-circuit | Yes; > 1 A (typ.) |
| Diagnostics indication LED: internal fault INTF (red) | Yes |
| Diagnostics indication LED: external fault EXTF (red) | Yes |
| Diagnostics indication LED: Status indicator digital output (green) | Yes |
| Potential separation digital outputs: between the channels | Yes |
|---|---|
| Potential separation digital outputs: between the channels, in groups of | 8 |
| Potential separation digital outputs: between the channels and backplane bus | Yes |
| Isolation tested with | 500 V DC |
|---|
| Width | 25 mm |
|---|---|
| Height | 290 mm |
| Depth | 210 mm |
| Weight, approx. | 600 g |
|---|
| Net weight | 0.842 kg |
|---|---|
| Country of origin | DE |
| Shipping weight | 1.342 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
No documents are on file for this part yet.
Ask us for the datasheetThe rated current of 6ES7422-7BL00-0AB0 is 0.5 A.
The tariff (HS) code on file for 6ES7422-7BL00-0AB0 is 85389091.
The EAN (GTIN) of 6ES7422-7BL00-0AB0 is 4025515128953.
6ES7422-7BL00-0AB0 ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Learn how a PLC works, including scan cycle, I/O sizing, IEC 61131-3 programming, and hardware selection for ABB, Schneider, and Siemens. Shop at Stoklink.
Master PLC system components: CPU, power supply, I/O modules, communication interfaces, and software with sizing formulas and selection tips. Shop at Stoklink.