Programmable Logic Controller Guide: Selection, Application, and Maintenance for Engineers
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Once production ends, supply depends on remaining stock.
No replacement announced yet. Tell us the application and we will propose an alternative.
The Siemens 6ES7422-1FH00-0AA0 SIMATIC S7-400 SM 422 module switches 16 isolated 120/230 V AC digital outputs at 2 A per channel, suitable for contactor coils and motor starters up to NEMA size 5. Each group of 4 channels carries its own 8 A, 250 V quick-response spare fuse, and response time is up to 100 ms. Isolation is tested at 1500 V AC.
Switching 120/230 V AC loads directly, this module suits contactor coils, indicator lamps, and small motor starters rated up to NEMA size 5 without an external relay interface. Each group of 4 channels carries its own 8 A, 250 V quick-response spare fuse, so a single overloaded channel does not necessarily take down the whole module. Response time is up to 100 ms per switching operation – factor that into any application needing fast AC switching. Because outputs are isolated in groups of 4 rather than individually, keep AC loads on the same phase and load-voltage class within one group.
| Load voltage L1: Rated value (AC) | 230 V; 120/230 V AC |
|---|---|
| Load voltage L1: permissible range, lower limit (AC) | 79 V |
| Load voltage L1: permissible range, upper limit (AC) | 264 V |
| Load voltage L1: permissible frequency range, lower limit | 47 Hz |
| Load voltage L1: permissible frequency range, upper limit | 63 Hz |
| from load voltage L+ (without load), max. | 1.5 mA |
|---|---|
| from backplane bus 5 V DC, max. | 400 mA |
| Power loss, typ. | 16 W |
|---|
| Part number | 6ES7422-1FH00-0AA0 |
|---|---|
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Phase-out announced by the manufacturer |
| EAN | 4019169046114 |
| Number of digital outputs | 16 |
|---|---|
| Short-circuit protection | Yes; Clocked electronically: Following a short-circuit, reclosing under a full load cannot be ensured. Countermeasures: change the signal at the output or interrupt the load voltage of the module. Briefly disconnect the load from the output. |
| required current for fuse shutdown, min. | 100 A |
| Response time, max. | 100 ms |
| Controlling a digital input | Yes; possible |
| Size of motor starters according to NEMA, max. | Size 5 according to NEMA |
| Spare fuses | Fuse 8 A, 250 V, quick response |
| Zero-crossing switch | No |
| Switching capacity of the outputs: on lamp load, max. | 50 W |
| Output voltage: for signal "1", min. | L1 (-18.1 V) |
| Output voltage: for signal "1" (at max. current), min. | L1 (-1.3 Vrms) |
| Output voltage: for signal "1" (at min. current), min. | L1 (-18.1 Vrms) |
| Output current: for signal "1" rated value | 2 A |
| Output current: for signal "1" permissible range, min. | 10 mA |
| Output current: for signal "1" permissible range, max. | 2 A |
| Output current: for signal "1" permissible surge current, max. | 50 A; per cycle |
| Output current: for signal "0" residual current, max. | 2.6 mA |
| Output delay with resistive load: "0" to "1", max. | 1 ms |
| Output delay with resistive load: "1" to "0", max. | 1 AC cycle |
| Parallel switching of two outputs: for redundant control of a load | Yes; Possible (only outputs with the same load voltage) |
| Switching frequency: with resistive load, max. | 10 Hz |
| Switching frequency: with inductive load, max. | 0.5 Hz |
| Switching frequency: with inductive load (acc. to IEC 60947-5-1, AC15), max. | 0.5 Hz |
| Switching frequency: on lamp load, max. | 1 Hz |
| Total current of the outputs (per group) all mounting positions: up to 40 °C, max. | 4 A; 6 A with fan assembly |
| Cable length: shielded, max. | 1 000 m |
| Cable length: unshielded, max. | 600 m |
| Diagnostics function | Not parameterizable |
|---|---|
| Diagnostics indication LED: internal fault INTF (red) | Yes; Fuse blown |
| Diagnostics indication LED: external fault EXTF (red) | Yes; Missing load voltage |
| Potential separation digital outputs: between the channels | Yes |
|---|---|
| Potential separation digital outputs: between the channels, in groups of | 4 |
| Potential separation digital outputs: between the channels and backplane bus | Yes |
| Isolation tested with | 1 500 V AC |
|---|
| Width | 25 mm |
|---|---|
| Height | 290 mm |
| Depth | 210 mm |
| Weight, approx. | 800 g |
|---|
| Net weight | 0.954 kg |
|---|---|
| Country of origin | DE |
| Shipping weight | 1.454 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
No documents are on file for this part yet.
Ask us for the datasheetThe rated current of 6ES7422-1FH00-0AA0 is 2 A.
The rated operational voltage of 6ES7422-1FH00-0AA0 is 120–230 V AC.
The tariff (HS) code on file for 6ES7422-1FH00-0AA0 is 85389091.
The EAN (GTIN) of 6ES7422-1FH00-0AA0 is 4019169046114.
6ES7422-1FH00-0AA0 ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Learn how a PLC works, including scan cycle, I/O sizing, IEC 61131-3 programming, and hardware selection for ABB, Schneider, and Siemens. Shop at Stoklink.
Master PLC system components: CPU, power supply, I/O modules, communication interfaces, and software with sizing formulas and selection tips. Shop at Stoklink.