Programmable Logic Controller Guide: Selection, Application, and Maintenance for Engineers
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Once production ends, supply depends on remaining stock.
No replacement announced yet. Tell us the application and we will propose an alternative.
The Siemens 6ES7422-1BL00-0AA0 SIMATIC S7-400 SM 422 module packs 32 isolated 24 V DC digital outputs rated 0.5 A each into one module slot for high channel density. Short-circuit protection trips between 0.75 and 1.5 A, and two outputs can be paralleled either to uprate current or for redundant load control. Rated current derates above 40 degrees C.
With 32 channels at 0.5 A each in the same module footprint, this variant trades per-channel current for I/O density – choose it over a higher-current, lower-channel-count module when driving many small 24 V DC loads (indicator lamps, small relays, PLC-to-PLC signaling) rather than motor starters that need more current per channel. Parallel switching of two outputs is supported both for uprating current and for redundancy, so two channels can be combined to exceed the 0.5 A single-channel rating. Current derates from 4 A total up to 40°C to 2 A per 8 adjacent outputs above 40°C – plan channel loading around that group boundary.
| Load voltage L+: Rated value (DC) | 24 V |
|---|---|
| Load voltage L+: permissible range, lower limit (DC) | 20.4 V |
| Load voltage L+: permissible range, upper limit (DC) | 28.8 V |
| from load voltage L+ (without load), max. | 30 mA |
|---|---|
| from backplane bus 5 V DC, max. | 200 mA |
| Power loss, typ. | 4 W |
|---|
| Part number | 6ES7422-1BL00-0AA0 |
|---|---|
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Phase-out announced by the manufacturer |
| EAN | 4025515128946 |
| Number of digital outputs | 32 |
|---|---|
| Short-circuit protection | Yes; Clocked electronically |
| Response threshold, typ. | 0.7 to 1.5 A |
| Limitation of inductive shutdown voltage to | -27 V |
| Controlling a digital input | Yes; possible |
| Switching capacity of the outputs: on lamp load, max. | 5 W |
| Load resistance range: lower limit | 48 Ω |
| Load resistance range: upper limit | 4 kΩ |
| Output voltage: for signal "1", min. | L+ (-0.3 V) |
| Output current: for signal "1" rated value | 0.5 A |
| Output current: for signal "1" permissible range, min. | 5 mA |
| Output current: for signal "1" permissible range, max. | 0.6 A |
| Output current: for signal "0" residual current, max. | 0.3 mA |
| Output delay with resistive load: "0" to "1", max. | 1 ms |
| Output delay with resistive load: "1" to "0", max. | 1 ms |
| Parallel switching of two outputs: for uprating | Yes; possible (only outputs of the same group) |
| Parallel switching of two outputs: for redundant control of a load | Yes; possible (only outputs of the same group) |
| Switching frequency: with resistive load, max. | 100 Hz |
| Switching frequency: with inductive load, max. | 0.5 Hz |
| Switching frequency: with inductive load (acc. to IEC 60947-5-1, DC13), max. | 2 Hz; 2 Hz at 0.3 A; 0.5 Hz at 0.5 A |
| Switching frequency: on lamp load, max. | 10 Hz |
| Total current of the outputs (per group) all mounting positions: up to 40 °C, max. | 4 A |
| Cable length: shielded, max. | 1 000 m |
| Cable length: unshielded, max. | 600 m |
| Diagnostics function | No |
|---|
| Potential separation digital outputs: between the channels | No |
|---|---|
| Potential separation digital outputs: between the channels, in groups of | 32 |
| Potential separation digital outputs: between the channels and backplane bus | Yes |
| Isolation tested with | 500 V AC/707 V DC, type test |
|---|
| Width | 25 mm |
|---|---|
| Height | 290 mm |
| Depth | 210 mm |
| Weight, approx. | 600 g |
|---|
| General Product Approval Miscellaneous | For use in hazard- |
|---|---|
| General Product Approval EMV | ous locations |
| Net weight | 0.774 kg |
|---|---|
| Country of origin | DE |
| Shipping weight | 1.274 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
No documents are on file for this part yet.
Ask us for the datasheetThe rated current of 6ES7422-1BL00-0AA0 is 0.5 A.
The tariff (HS) code on file for 6ES7422-1BL00-0AA0 is 85389091.
The EAN (GTIN) of 6ES7422-1BL00-0AA0 is 4025515128946.
6ES7422-1BL00-0AA0 ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Learn how a PLC works, including scan cycle, I/O sizing, IEC 61131-3 programming, and hardware selection for ABB, Schneider, and Siemens. Shop at Stoklink.
Master PLC system components: CPU, power supply, I/O modules, communication interfaces, and software with sizing formulas and selection tips. Shop at Stoklink.