Programmable Logic Controller Guide: Selection, Application, and Maintenance for Engineers
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
The Siemens 6ES7143-4BF50-0AA0 is a SIMATIC ET 200pro electronic module with 4 digital inputs and 4 digital outputs, rated 24 V DC. Each output switches up to 0.5 A with electronic short-circuit protection per channel, and the module reports diagnostic status back to the controller. It mounts on the ET 200pro bus module and requires a separate connection module (6ES7194-4..00-0AA0).
This module pairs 4 inputs with 4 outputs on one channel block, useful when a station needs a small balanced I/O count instead of a dedicated 8-channel input or output card. The 0.5 A per-output rating and 2 A module-wide ceiling set the limit for how many loads run at once across the four outputs; heavier loads need a load relay ahead of the channel. Diagnostics report at module level, so it suits lamp, solenoid and valve-pilot outputs more than channels needing individually reported wire-break status.
Fits ET 200pro stations needing a small balanced digital I/O block, such as one interlock circuit with a few pilot-lamp or valve outputs and matching feedback inputs. The 24 V DC P-reading (sourcing) inputs match standard European 24 V field wiring without added signal conditioning.
| Load voltage 2L+: Rated value (DC) | 24 V |
|---|---|
| Load voltage 2L+: Short-circuit protection | Yes |
| Load voltage 2L+: Reverse polarity protection | Yes |
| from load voltage 2L+ (without load), max. | 20 mA |
|---|---|
| from backplane bus 3.3 V DC, max. | 20 mA |
| Short-circuit protection | Yes; per module, electronic |
|---|---|
| Output current: up to 55 °C, max. | 1 A |
| Part number | 6ES7143-4BF50-0AA0 |
|---|---|
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Active, in production |
| EAN | 4025515081760 |
| ETIM class | EC001599 |
| eCl@ss | 27242604 |
| Power loss, typ. | 2 W |
|---|
| Number of digital inputs | 4 |
|---|---|
| Sourcing/sinking input | P-reading |
| Input characteristic curve in accordance with IEC 61131, type 3 | Yes |
| Input voltage: Rated value (DC) | 24 V |
| Input voltage: for signal "0" | -3 to +5V |
| Input voltage: for signal "1" | +11 to +30V |
| Input current: for signal "1", typ. | 7 mA |
| Input delay (for rated value of input voltage) for standard inputs: at "0" to "1", max. | 3 ms |
| Cable length: unshielded, max. | 30 m |
| Number of digital outputs | 4 |
|---|---|
| Current-sourcing | Yes |
| output type acc. to IEC 61131, type 0.5 | Yes |
| Short-circuit protection | Yes; per channel, electronic |
| Response threshold, typ. | 0.7 A |
| Limitation of inductive shutdown voltage to | Typ. (2L+) -47 V |
| Controlling a digital input | Yes |
| Switching capacity of the outputs: on lamp load, max. | 5 W |
| Load resistance range: lower limit | 48 Ω |
| Load resistance range: upper limit | 4 kΩ |
| Output voltage: for signal "1", min. | 2L+ (-0,8 V) |
| Output current: for signal "1" rated value | 0.5 A |
| Output current: for signal "0" residual current, max. | 0.5 mA |
| Parallel switching of two outputs: for uprating | No |
| Parallel switching of two outputs: for redundant control of a load | Yes |
| Switching frequency: with resistive load, max. | 100 Hz |
| Switching frequency: with inductive load, max. | 0.5 Hz |
| Switching frequency: on lamp load, max. | 1 Hz |
| Total current of the outputs (per group) all mounting positions: up to 55 °C, max. | 2 A |
| Cable length: unshielded, max. | 30 m |
| Connectable encoders: 2-wire sensor | Yes |
|---|---|
| Connectable encoders: permissible quiescent current (2-wire sensor), max. | 1.5 mA |
| Diagnostics function | Yes |
|---|---|
| Alarms: Diagnostic alarm | Yes |
| Diagnoses: Diagnostic information readable | Yes |
| Diagnoses: Short-circuit | Yes; Short-circuit of outputs to ground; module by module |
| Diagnostics indication LED: Status indicator digital input (green) | Yes |
| Diagnostics indication LED: Status indicator digital output (green) | Yes |
| between backplane bus and all other circuit components | Yes |
|---|---|
| Potential separation digital inputs: between the channels | No |
| Potential separation digital inputs: between the channels and backplane bus | Yes |
| Potential separation digital outputs: between the channels | No |
| Potential separation digital outputs: between the channels and backplane bus | Yes |
| Isolation tested with | 707 V DC (type test) |
|---|
| Width | 45 mm |
|---|---|
| Height | 130 mm |
| Depth | 35 mm |
| Weight, approx. | 140 g |
|---|
| eClass | 9 27-24-26-04 |
|---|---|
| ETIM | 10 EC001599 |
| IDEA | 4 3566 |
| UNSPSC | 15 32-15-17-05 |
| China RoHS Manufacturer Declara- | tion |
|---|
| Net weight | 0.173 kg |
|---|---|
| Country of origin | DE |
| Shipping weight | 0.673 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
No documents are on file for this part yet.
Ask us for the datasheetThe rated current of 6ES7143-4BF50-0AA0 is 0.5 A.
The rated operational voltage of 6ES7143-4BF50-0AA0 is 24 V AC.
The tariff (HS) code on file for 6ES7143-4BF50-0AA0 is 85389091.
The EAN (GTIN) of 6ES7143-4BF50-0AA0 is 4025515081760.
6ES7143-4BF50-0AA0 ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Learn how a PLC works, including scan cycle, I/O sizing, IEC 61131-3 programming, and hardware selection for ABB, Schneider, and Siemens. Shop at Stoklink.
Master PLC system components: CPU, power supply, I/O modules, communication interfaces, and software with sizing formulas and selection tips. Shop at Stoklink.