Part number
6ES7142-5AF00-0BL0
Model no
IO-Link DQ 8x24VDC/2A
$184.23 On request Dispatch — · From TürkiyeGet a Quote
SIMATIC ET 200AL

Siemens 6ES7142-5AF00-0BL0 SIMATIC ET 200AL IO-Link DQ 8x24VDC/2A 8xM12 Remote I/O Module

SIMATIC ET 200AL IO-Link DQ module, 8x 24V DC/2A outputs, 8xM12 connectors, IP65/67.

Rated current
2 A
Communication
IO-Link 1.1
Display
Green channel-status LED + green/red module diagnostics LED
EAN
4047623411390
Description

About the IO-Link DQ 8x24VDC/2A

The Siemens 6ES7142-5AF00-0BL0 is a SIMATIC ET 200AL IO-Link output module with 8 channels rated 2 A at 24 V DC, wired through 8x M12 connectors and communicating over IO-Link 1.1 at 38.4 kBd. Output current derates from 2 A at 45 degC to 1 A at 55 degC, and the module is suitable for safety-related tripping of standard modules to PL d / SIL 2 from firmware FS01.

Selection Notes

Pick the IO-Link variant over the standard hard-wired DQ module when the IO-Link master needs to configure or monitor the output channel state remotely, at the cost of an 8 A total output budget instead of 2 A per channel available on every port simultaneously. The current rating derates from 2 A at 45 degC to 1 A at 55 degC, so a hot cabinet-free installation near the top of that range needs the load sized against 1 A, not the nameplate 2 A. PL d / SIL 2 safety-related tripping support from firmware FS01 still applies, same as the non-IO-Link version.

Applications

Field-mounted actuator control on IO-Link networks - solenoid valves, indicator lamps, and small loads up to 2 A per channel where the IO-Link master needs diagnostic or configuration access to the output module itself.

Specification

Full specification

85 values · Last verified 01 Nov 2026

General information 6

Product type designation IO-Link DQ 8x24VDC/2A
HW functional status FS01
Firmware version V1.0.x
Vendor identification (VendorID) 42
Device identifier (DeviceID) 229381
Engineering with: IODD file Yes

Supply voltage 8

Load voltage 1L+: Rated value (DC) 24 V; Supply from 1Us+ of the IO-Link master
Load voltage 1L+: permissible range, lower limit (DC) 18 V
Load voltage 1L+: permissible range, upper limit (DC) 30 V
Load voltage 1L+: Reverse polarity protection Yes; against destruction
Load voltage 2L+: Rated value (DC) 24 V; Supply via M12 connector L-coded
Load voltage 2L+: permissible range, lower limit (DC) 20.4 V
Load voltage 2L+: permissible range, upper limit (DC) 28.8 V
Load voltage 2L+: Reverse polarity protection Yes; against destruction; load increasing

Input current 2

Current consumption (rated value) 12 mA; without load
from load voltage 2L+, max. 8 A; Maximum value
Show all 85 specifications ↓ Show less ↑69 more values in Identification, Power loss, Digital outputs, IO-Link, Interrupts/diagnostics/status information, Potential separation, Isolation, Degree and class of protection, Standards, approvals, certificates, Ambient conditions, Connection method, Dimensions, Version Classification, General Product Approval Functional Saftey, Logistics.

Identification 10

Part number 6ES7142-5AF00-0BL0
Type designation IO-Link DQ 8x24VDC/2A
Brand Siemens
Condition New, factory sealed
Source Siemens and its authorised distributors
Warranty Manufacturer warranty
Lifecycle status Active, in production
EAN 4047623411390
ETIM class EC001599
eCl@ss 27242604

Power loss 1

Power loss, typ. 3.6 W

Digital outputs 18

Number of digital outputs 8
Current-sourcing Yes
output type acc. to IEC 61131, type 2 Yes
Short-circuit protection Yes; per channel, electronic
Response threshold, typ. 2.8 A
Limitation of inductive shutdown voltage to Switching capacity of the outputs 2L+ (-47 V)
on lamp load, max. 10 W
Load resistance range: lower limit 12 Ω
Load resistance range: upper limit 4 kΩ
Output voltage: for signal "1", min. L+ (-0.8 V)
Output current: for signal "1" rated value 2 A (45 °C); 1 A (55 °C)
Output current: for signal "1" permissible range, max. 2 A; with inductive load to IEC 60947-5-1, DC-13 / AC-15
Output current: for signal "0" residual current, max. 0.5 mA
Switching frequency: with resistive load, max. 100 Hz
Switching frequency: with inductive load, max. 0.1 Hz; 0.25 Hz at 25 °C
Switching frequency: on lamp load, max. 1 Hz
Total current of the outputs: Current per module, max. 8 A
Cable length: unshielded, max. 30 m

Interrupts/diagnostics/status information 6

Substitute values connectable Yes; channel by channel, parameterizable
Alarms: Diagnostic alarm Yes; Parameterizable
Diagnoses: short-circuit Yes; Outputs to ground; module by module
Diagnostics indication LED: Channel status display Yes; green LED
Diagnostics indication LED: for module diagnostics Yes; green/red LED
Diagnostics indication LED: For load voltage monitoring Yes; green LED

Potential separation 3

between the load voltages Yes
Potential separation channels: between the channels No
Potential separation channels: between the channels and the power supply of the electronics Yes

Isolation 1

Isolation tested with 707 V DC (type test)

Degree and class of protection 1

IP degree of protection IP65/67

Standards, approvals, certificates 2

Suitable for safety-related tripping of standard modules Yes; from FS01
Highest safety class achievable for safety-related tripping of standard modules: Performance level according to ISO 13849-1 PL d

Ambient conditions 2

Ambient temperature during operation: min. -30 °C
Ambient temperature during operation: max. 55 °C

Connection method 3

Design of electrical connection for the inputs and outputs M12, 5-pin, A-coded
Type of electrical connection for IO-Link M12, 5-pin, A-coded
Design of electrical connection for supply voltage M12, 4-pin, L-coded

Dimensions 2

Width 45 mm
Height 159 mm

Version Classification 4

eClass 16 27-24-26-04
ETIM 10 EC001599
IDEA 4 3566
UNSPSC 15 32-15-17-05

General Product Approval Functional Saftey 2

China RoHS Manufacturer Declara- TUEV tion
Maritime application NK / Nippon Kaiji Ky- okai

Logistics 6

Net weight 0.193 kg
Country of origin DE
Shipping weight 0.693 kg
Ships from Türkiye
Dispatch —
Stock On request

Source: manufacturer data · Last verified: 01 Nov 2026

Documents

Documents for 6ES7142-5AF00-0BL0

No documents are on file for this part yet.

Ask us for the datasheet
Quick answers

Questions about the IO-Link DQ 8x24VDC/2A

What is the rated current of IO-Link DQ 8x24VDC/2A?

The rated current of IO-Link DQ 8x24VDC/2A is 2 A.

What is the HS code of IO-Link DQ 8x24VDC/2A for customs?

The tariff (HS) code on file for IO-Link DQ 8x24VDC/2A is 85389091.

What is the EAN of IO-Link DQ 8x24VDC/2A?

The EAN (GTIN) of IO-Link DQ 8x24VDC/2A is 4047623411390.

Where does IO-Link DQ 8x24VDC/2A ship from, and how fast?

IO-Link DQ 8x24VDC/2A ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.

Guides

Guides for PLC & controllers

All guides for PLC & controllers
Reviews

Customer reviews

Series

Siemens SIMATIC ET 200AL

Brand
Siemens
Series
SIMATIC ET 200AL
$184.23 On request
Get a Quote
Quote

Get a Quote

IO-Link DQ 8x24VDC/2A

Genuine parts

Genuine, factory-sealed parts

Siemens · 6ES7142-5AF00-0BL0

Every part on Stoklink is new, unused and made by the manufacturer named on the page.

Condition
New and unused, in the manufacturer's factory-sealed packaging.
Sourced from
Siemens and its authorised distributors.
Warranty
The manufacturer's warranty applies.
If a part is not genuine
We refund the full amount.

Added to cart Could not add to cart

View cart