Programmable Logic Controller Guide: Selection, Application, and Maintenance for Engineers
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
The Siemens 6ES7142-4BD00-0AA0 is a SIMATIC ET 200pro digital output module with 4 channels rated 2.0 A at 24 V DC, current-sourcing per IEC 61131 type 2 and short-circuit protected per channel. It is suitable for safety-related tripping of standard modules to Performance Level d (Category 3) and SIL 2, and switches resistive loads at up to 100 Hz.
The 2.0 A per-channel rating covers small DC motor loads, solenoids, and contactor coils that a 0.5 A output module cannot switch directly, and two channels can be paralleled for redundant control of a single load. Because it is suitable for safety-related tripping of standard modules to PL d / SIL 2, a fail-safe CPU can drive a standard (non-F) actuator through this channel without a dedicated F-DQ module, provided the rest of the safety chain meets the same category. The module still needs its own bus module and I/O connection module, ordered separately, to complete the backplane slot.
Actuator control in distributed SIMATIC ET 200pro stations - solenoid valves, small contactor coils, and DC motor loads up to 2 A on 24 V DC machine lines, including outputs that must trip from a safety PLC's standard channel.
| Load voltage 2L+: Rated value (DC) | 24 V |
|---|---|
| Load voltage 2L+: Short-circuit protection | Yes; per channel, electronic |
| Load voltage 2L+: Reverse polarity protection | Yes; against destruction; load increasing |
| from load voltage 2L+ (without load), max. | 20 mA |
|---|---|
| from backplane bus 3.3 V DC, max. | 20 mA |
| Power loss, typ. | 2 W |
|---|
| Part number | 6ES7142-4BD00-0AA0 |
|---|---|
| Brand | Siemens |
| Condition | New, factory sealed |
| Source | Siemens and its authorised distributors |
| Warranty | Manufacturer warranty |
| Lifecycle status | Active, in production |
| EAN | 4025515072195 |
| ETIM class | EC001599 |
| eCl@ss | 27242604 |
| Address space per module: Address space per module, max. | 1 byte |
|---|
| Number of digital outputs | 4 |
|---|---|
| Current-sourcing | Yes |
| output type acc. to IEC 61131, type 2 | Yes |
| Short-circuit protection | Yes |
| Response threshold, typ. | 2.8 A |
| Limitation of inductive shutdown voltage to | 2L+ (-47 V) |
| Controlling a digital input | Yes |
| Switching capacity of the outputs: on lamp load, max. | 10 W |
| Load resistance range: lower limit | 12 Ω |
| Load resistance range: upper limit | 4 kΩ |
| Output voltage: for signal "1", min. | 2L+ (-0,8 V) |
| Output current: for signal "1" rated value | 2 A |
| Output current: for signal "0" residual current, max. | 0.5 mA |
| Parallel switching of two outputs: for uprating | No |
| Parallel switching of two outputs: for redundant control of a load | Yes |
| Switching frequency: with resistive load, max. | 100 Hz |
| Switching frequency: with inductive load, max. | 0.5 Hz |
| Switching frequency: on lamp load, max. | 1 Hz |
| Total current of the outputs (per group) all mounting positions: up to 55 °C, max. | 4 A |
| Cable length: shielded, max. | 30 m |
| Cable length: unshielded, max. | 30 m |
| Diagnostics function | Yes |
|---|---|
| Alarms: Diagnostic alarm | Yes |
| Diagnoses: Diagnostic information readable | Yes |
| Diagnoses: Short-circuit | Yes; Short-circuit of outputs to ground; module by module |
| Diagnostics indication LED: Group error SF (red) | Yes |
| Diagnostics indication LED: Status indicator digital output (green) | Yes |
| between backplane bus and all other circuit components | Yes |
|---|---|
| Potential separation digital outputs: between the channels | No |
| Potential separation digital outputs: between the channels and backplane bus | Yes |
| Isolation tested with | 707 V DC (type test) |
|---|
| Suitable for safety-related tripping of standard modules | Yes |
|---|---|
| Highest safety class achievable for safety-related tripping of standard modules: Performance level according to ISO 13849-1 | PL d |
| Width | 45 mm |
|---|---|
| Height | 130 mm |
| Depth | 35 mm |
| Weight, approx. | 140 g |
|---|
| Net weight | 0.17 kg |
|---|---|
| Country of origin | DE |
| Shipping weight | 0.67 kg |
| Ships from | Türkiye |
| Dispatch | — |
| Stock | On request |
Source: manufacturer data · Last verified: 01 Nov 2026
No documents are on file for this part yet.
Ask us for the datasheetThe rated current of 6ES7142-4BD00-0AA0 is 2 A.
The tariff (HS) code on file for 6ES7142-4BD00-0AA0 is 85389091.
The EAN (GTIN) of 6ES7142-4BD00-0AA0 is 4025515072195.
6ES7142-4BD00-0AA0 ships from Türkiye. Shipping calculated at checkout · import duties and taxes paid on arrival.
PLC selection guide for engineers covering IEC 61131 compliance, Siemens, Rockwell, Schneider, ABB comparison, scan time sizing, and wiring. Shop at Stoklink.
Learn how a PLC works, including scan cycle, I/O sizing, IEC 61131-3 programming, and hardware selection for ABB, Schneider, and Siemens. Shop at Stoklink.
Master PLC system components: CPU, power supply, I/O modules, communication interfaces, and software with sizing formulas and selection tips. Shop at Stoklink.