- Home
- I/O Modules & Remote I/O
- Siemens 6ES7132-7GD00-0AB0 SIMATIC ET 200iSP 4DQ 23.1VDC/20mA L-Shutdown Ex ib Remote I/O Module Siemens 6ES7132-7GD00-0AB0 SIMATIC ET 200iSP 4DQ 23.1VDC/20mA L-Shutdown Ex ib Remote I/O Module
Siemens 6ES7132-7GD00-0AB0 SIMATIC ET 200iSP 4DQ 23.1VDC/20mA L-Shutdown Ex ib Remote I/O Module
Siemens 6ES7132-7GD00-0AB0 SIMATIC ET 200iSP 4DQ 23.1VDC/20mA L-Shutdown Ex ib Remote I/O Module
Get Quote
- Description
The Siemens 6ES7132-7GD00-0AB0 is a SIMATIC ET 200iSP electronic module with 4 intrinsically safe digital outputs rated 23.1 V DC at 20 mA, built for Ex ib (ia Ga) IIC T4 Gb gas zones and Ex ib [ia IIIC Da] IIC T4 Gb dust zones with an L-shutdown input circuit. It mounts on the ET200iSP rail with screw or spring terminals and IP30 protection.
Technical Specifications
| Catalog No | 6ES7132-7GD00-0AB0 |
| SKU | 6ES7132-7GD00-0AB0 |
| Brand | Siemens |
| Series | SIMATIC ET 200iSP |
| Product type designation | 4DQ 23.1 V DC/20 mA |
| HW functional status | 7 |
| Firmware version | V3.0.0 |
| Product version | SHUT DOWN L |
| Digital outputs | 4, transistor, plus 1 intrinsically safe input for L shutdown |
| No-load voltage Uao (DC) | 23.1 V |
| Internal resistor Ri | 275 ohm |
| Output current, signal 1, rated | 0.02 A |
| Short-circuit protection | Yes |
| Switching frequency, resistive load, max. | 100 Hz |
| Switching frequency, inductive load, max. | 2 Hz |
| Output delay 0 to 1 / 1 to 0, max. | 2 ms / 1.5 ms |
| Uo / Io / Po (gas group IIC), max. | 25.6 V / 96 mA / 0.61 W |
| Co / Lo (gas group IIC), max. | 98 nF / 3 mH |
| Ui / Pi / Ci (input circuit), max. | 28 V / 1.2 W / 3 nF |
| ATEX marking | II 2 G (1) G Ex ib [ia Ga] IIC T4 Gb, II 2 G (1) D Ex ib [ia IIIC Da] IIC T4 Gb, I M2 Ex ib [ia] I Mb |
| Degree of protection | IP30 |
| Current consumption, typ. / max. | 290 mA / 340 mA |
| Power loss, typ. | 2.5 W |
| Cable length, shielded / unshielded, max. | 500 m / 500 m |
| Connection method | Screw/spring-type terminal |
| Dimensions (W x H x D) | 30 x 129 x 136.5 mm |
| Weight, approx. | 255 g |
Certifications & Standards
- GL
- ABS
- BV
- DNV
Selection Notes
The Ex ib rating (rather than the higher Ex ia grade) means this output circuit is intrinsically safe under a single fault, which is enough for Zone 1 gas and Zone 21 dust areas but not Zone 0. Check the 25.6 V / 96 mA / 0.61 W Uo/Io/Po loop values against the field-side barrier and cable capacitance before wiring a solenoid or pilot light into this circuit. This module carries the L-shutdown input; the otherwise identical H-shutdown variant differs only in that intrinsically safe shutdown-circuit threshold, so pick between them according to what the loop's safety documentation specifies.